Nissan Navara D22 ZD30 Turbo Oil Line Guide

Fitment & Selection Guide

Nissan Navara D22 ZD30Turbo Oil Line & Fitting Guide

This guide covers GryphonTek oil feed lines, oil drain hose kits and -4AN fittings for Nissan Navara D22 models with the ZD30DDT 3.0L diesel engine and a factory HT12-19B or HT12-19D turbocharger.

Check your vehicle and turbo, choose a complete feed and return kit or individual lines, and identify the engine side and turbo side fittings before ordering.

Navara D22ZD30DDT 3.0L DieselHT12-19B / HT12-19D
Choose a section to readBrowse Kits & Fittings

Which Turbo Oil Line Kit Do You Need?

Start with the part you need to replace. A complete kit covers both sides of the turbo oil circuit; individual line kits suit a repair limited to the feed or drain side.

  • Replacing both oil lines

    Choose the Oil Feed & Return Line Kit. It combines a -4AN PTFE braided feed line, NBR drain hose, fittings and return hardware for the listed factory turbo setup.

  • Replacing the oil feed pipe

    Choose the Oil Feed Line Kit when the supply line needs replacement and the drain assembly remains serviceable.

  • Replacing the oil drain hose assembly

    Choose the Oil Drain Hose Kit when work is limited to the return side.

  • Connecting a suitable -4AN line at the turbo

    Choose the Turbo Oil Feed Fitting Kit for the listed HT12-19B / HT12-19D inlet connection.

  • Connecting a suitable -4AN line at the engine

    Choose the Engine Block Oil Fitting Kit for the ZD30DDT engine side supply connection.

Check the included parts list before adding separate fittings. A line kit may already supply the fittings needed for its intended installation.

Oil Feed and Oil Drain: Different Jobs

Oil Feed Line

The feed line carries pressurized engine oil to the turbocharger. GryphonTek's listed D22 feed line uses a pre-crimped -4AN PTFE hose with stainless steel braid to replace the original rigid pipe.

Match the connections at both ends and check the route around the exhaust side before installation.

Oil Drain / Return Line

The drain carries oil away from the turbocharger and back to the engine by gravity. The listed D22 drain kit uses an NBR hose with a flange, gasket and fastening hardware.

A clear, downward return path matters. Kinks, low loops or an uphill section can hold oil in the drain.

Locate the leak before choosing a kit. Inspect the feed connections, drain flange, hose and sealing surfaces. Oil visible below the turbo may have travelled from a connection above it.

Replacing a hose alone will not correct every cause of turbo oil leakage. Drain blockage and crankcase ventilation problems should be checked as part of the repair.

Vehicle & Turbo Compatibility

Use the vehicle, engine and turbo together to check fitment. The references below are listed for this D22 oil line range.

Vehicle Nissan Navara D22
Engine ZD30DDT 3.0L diesel
Factory turbo HT12-19B / HT12-19D
Nissan turbo references 14411-9S000 / 14411-9S00A / 14411-9S002
Oil feed pipe reference 15192-9S000
Oil drain pipe reference 15197-9S000

Do not order by the ZD30 or NP300 name alone. Confirm the D22 chassis, engine code and turbo connections. Fitment for Patrol models, other Navara engines or a different turbo must be checked separately.

Part numbers help narrow the application, but the fitted turbo and line layout still need to match. For an aftermarket replacement or modified turbo, compare the inlet, drain connection, mounting position and hose route before ordering.

Engine Side vs Turbo Side Fittings

Engine Block Oil Fitting

This is the connection at the engine oil supply outlet. Select the engine side fitting for a suitable -4AN braided feed line setup on the listed ZD30DDT engine.

View Engine Side Fitting Options

Turbo Oil Feed Fitting

This is the connection at the turbo oil inlet. The listed fitting kit is intended for the factory HT12-19B / HT12-19D turbo and a suitable -4AN feed line.

View Turbo Side Fitting Options

Adapter fitting or banjo bolt? Both product pages offer fitting options. Match the option to the original connection arrangement, the intended hose end setup and available clearance. Check the product photos as well as the option name.

Oil feed restriction: The listed HT12-19 feed line, feed and return kit, and turbo side fitting kit specify a 1.8 mm restricted port. Treat this as a specification of those products. A different turbo needs its own oil supply requirements checked before a restrictor is selected or changed.

Installation Notes

Compare the new kit with the existing connections before removing the original lines. Work should follow the vehicle and turbo manufacturer's service instructions.

  1. Check the full route. Confirm both connection points, hose length and clearance around the exhaust, brackets and nearby components.
  2. Keep the oil passages clean. Prevent debris entering the fittings. Use the specified sealing washers and gaskets.
  3. Protect the feed line. Route it clear of hot surfaces and sharp edges. Avoid hose twist, tight bends or pulling the end fittings into position.
  4. Keep the drain flowing downhill. Avoid kinks, low loops and sections that rise before reaching the engine return connection.
  5. Check before road use. Follow the applicable oil priming procedure, inspect for leaks at start up and recheck the engine oil level. Correct any leak before driving.

Frequently Asked Questions

Will these kits fit every ZD30 engine?
These line kits are listed for Navara D22 ZD30DDT models with the specified HT12-19B / HT12-19D turbo setup. Check other vehicles and turbo combinations separately.
Do I need separate fittings with the complete kit?
The listed feed and return kit includes feed fittings and return hardware. Review its included parts list before ordering extra fittings. Separate fitting kits are useful when building or repairing a suitable -4AN line setup.
What if my turbo has been upgraded or changed?
Check fitment before ordering. Email gryphon@gryphontek.com with the vehicle and engine details, turbo part number and clear photos of the engine side supply, turbo oil inlet and drain connections.
Kits & Fittings

Browse Navara D22 ZD30 Oil Line Kits

Oil Feed Only

Turbo Oil Feed Line Kit

Replace the factory feed pipe with a pre-crimped -4AN PTFE stainless steel braided line. Listed against oil feed pipe reference 15192-9S000 for the specified HT12-19 turbo application.

View Product Details
Oil Drain Only

Turbo Oil Drain Hose Kit

Service the turbo oil return side with an NBR hose, drain flange, gasket, bolts and clamps. Listed against oil drain pipe reference 15197-9S000 for the specified D22 turbo setup.

View Product Details
Turbo Side Connection

Turbo Oil Feed Fitting Kit

Connect a suitable -4AN feed line at the HT12-19B / HT12-19D oil inlet. Choose the fitting option that matches your installation. The listed kit specifies a 1.8 mm restricted port.

View Product Details
Engine Side Connection

Engine Block Oil Fitting Kit

Provide the engine side connection for a suitable -4AN braided oil feed line on the listed D22 ZD30DDT engine. Adapter fitting and banjo bolt options are available.

View Product Details

Shop Navara D22 ZD30 Turbo Oil Lines

Browse oil feed and return kits, individual feed lines, drain hose kits and -4AN fittings for the listed Navara D22 ZD30DDT turbo setup.

Shop D22 ZD30 Oil Lines & Fittings